{"id":1580,"date":"2019-01-03T10:32:18","date_gmt":"2019-01-03T10:32:18","guid":{"rendered":"http:\/\/al-tet-onlinesales.allyoulovetrading.com\/?post_type=product&p=1580"},"modified":"2019-01-03T10:32:18","modified_gmt":"2019-01-03T10:32:18","slug":"cj1w-nc3-2","status":"publish","type":"product","link":"https:\/\/al-tet-onlinesales.adbridgessolution.com\/index.php\/product\/cj1w-nc3-2\/","title":{"rendered":"CJ1W-NC[][]3"},"content":{"rendered":"
\n
\n

\u2022 Two types to choose from: open collector output and line driver. Because both open collector output and line driver types feature 1-, 2-, and 4-axis models, the most appropriate model can be selected for the application at hand.<\/p>\n

\u2022 Positioning START occurs within 2 ms (maximum speed) after receiving a command from the Programmable Controller.<\/p>\n

\u2022 High-speed data transfer is possible using INTELLIGENT I\/O WRITE (IOWR) and INTELLIGENT I\/O READ (IORD) instructions.<\/p>\n

\u2022 Fine control from low to high speed (500 kpps max.) is possible in 1-pps units.<\/p>\n

\u2022 Positioning can be done from memory, by writing an operating pattern into the PCU memory in advance. Three position patterns \u2212 Terminating, Automatic, and Continuous \u2212 can be set with completion codes to respond to a wide range of operations. Positioning of up to 100 patterns (sequential data) per one axis can be possible.<\/p>\n

\u2022 Positioning (direct operation) can be done by direct PLC ladder commands for position data, speed data, and acceleration data. This simplifies control in situations when the target position and speed cannot be decided until immediately before operation begins, or when the target position and speed change due to other circumstances. The target position and speed can also be changed during operation.<\/p>\n

\u2022 Interrupt feeding moves the axis a specified amount, then stops it, in accordance with an interrupt input. High-speed (0.1 ms max.) processing of the interrupt input signal ensures high-precision interrupt positioning. This helps to maximize feeder precision.<\/p>\n

\u2022 Easy-to-Use positioning can be possible with versatile functions such as Teaching, Override, Backlash compensation, Zones, Forced interrupt and Acceleration\/Deceleration curve.<\/p>\n<\/div>\n<\/div>\n

 <\/p>\n

International Standards<\/h4>\n
\n
\n
    \n
  • The standards are abbreviated as follows: U: UL, U1: UL(Class I Division 2 Products for Hazardous Locations), C: CSA, UC: cULus, UC1: cULus (Class I Division 2 Products for Hazardous Locations), CU: cUL, N: NK, L: Lloyd, and CE: EC Directives.<\/li>\n
  • Contact your OMRON representative for further details and applicable conditions for these standards.<\/li>\n<\/ul>\n<\/div>\n<\/div>\n

    Position Control Unit<\/h4>\n
    \n
    \n
    \n\n\n\n\n\n\n\n\n\n\n\n
    Unit
    \ntype<\/strong><\/th>\n    		Name<\/strong><\/td>\nSpecifications<\/strong><\/th>\nNo. of
    \nunit
    \nnumbers
    \nallocated<\/strong><\/td>\n    		Current
    \nconsumption (A)<\/strong><\/th>\n    		Model<\/strong><\/td>\nStandards<\/strong><\/th>\n<\/tr>\n
    Control method\/
    \nControl output
    \ninterface<\/strong><\/th>\n    		Number of
    \ncontrol
    \naxes<\/strong><\/td>\n    		5 V
    \nsystem<\/strong><\/th>\n    		24 V
    \nsystem<\/strong><\/td>\n<\/tr>\n
    CJ1
    \nSpecial
    \nI\/O
    \nUnits<\/strong><\/th>\n    		Position
    \ncontrol
    \nunit<\/strong><\/p>\n
    <\/strong><\/div>\n<\/td>\n
    		Open-loop control
    \nby pulse train
    \noutput\/Open-
    \ncollector output<\/td>\n    		1 axis<\/td>\n1<\/td>\n0.25<\/td>\n—<\/td>\nCJ1W-NC113<\/strong><\/td>\nUC1, CE<\/td>\n<\/tr>\n
    2 axes<\/td>\n0.25<\/td>\n—<\/td>\nCJ1W-NC213<\/strong><\/td>\n<\/tr>\n
    4 axes *<\/td>\n2<\/td>\n0.36<\/td>\n—<\/td>\nCJ1W-NC413<\/strong><\/td>\n<\/tr>\n
    Open-loop control
    \nby pulse train
    \noutput\/Line-driver
    \noutput<\/td>\n    		1 axis<\/td>\n1<\/td>\n0.25<\/td>\n—<\/td>\nCJ1W-NC133<\/strong><\/td>\n<\/tr>\n
    2 axes<\/td>\n0.25<\/td>\n—<\/td>\nCJ1W-NC233<\/strong><\/td>\n<\/tr>\n
    4 axes *<\/td>\n2<\/td>\n0.36<\/td>\n—<\/td>\nCJ1W-NC433<\/strong><\/td>\n<\/tr>\n
    Space
    \nUnit<\/strong><\/th>\n    		The ambient operation temperature range can be increased to
    \n0 to 55 \u00b0C if the CJ1W-SP001 CJ-series Space Unit is used.<\/td>\n    		CJ1W-SP001<\/strong><\/td>\nUC1, CE<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n<\/div>\n
    \n
    \n
    Note: This unit cannot be used with the Machine Automation Controller NJ-series.
    \n* The ambient operating temperature of the CJ1W-NC413\/NC433 is 0 to 50\u00b0C. Allowable power supply voltage range for
    \nexternal power supply is 22.8 to 25.2 V DC.<\/div>\n<\/div>\n<\/div>\n

    Software<\/h4>\n
    \n
    \n
    \n\n\n\n\n
    Name<\/strong><\/th>\nSpecifications<\/strong><\/th>\nNumber of
    \nlicenses<\/strong><\/th>\n    		Model<\/strong><\/th>\nStand-
    \nards<\/strong><\/th>\n<\/tr>\n
    FA Integrated
    \nTool Package
    \nCX-One
    \nVer.4.[]<\/strong><\/th>\n    		The CX-One is a comprehensive software package
    \nthat integrates Support Software for OMRON PLCs
    \nand components. CX-One runs on the following OS.
    \nOS: Windows XP (Service Pack 3 or higher, 32-bit
    \nversion)\/Windows Vista (32-bit\/64-bit version)\/
    \nWindows 7 (32-bit\/64-bit version)\/Windows 8 (32-
    \nbit\/64-bit version)\/Windows 8.1 (32-bit\/64-bit
    \nversion)\/Windows 10 (32-bit\/64-bit version)<\/p>\n

    CX-One Ver.4. [] includes CX-Position Ver.2. [].
    \nFor details, refer to the CX-One catalog (Cat. No.
    \nR134).<\/td>\n

    		1 license *
    \nDVD<\/td>\n    		CXONE-AL01D-V4<\/strong><\/td>\n—<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n<\/div>\n
    \n
    \n

    * Multi licenses (3, 10, 30, or 50 licenses) and DVD media without licenses are also available for the CX-One.<\/p>\n<\/div>\n<\/div>\n

    Servo Relay Unit\/Cables<\/h4>\n
    \n
    \n
    \n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
    Name<\/strong><\/th>\nApplicable units<\/strong><\/th>\nApplicable drives<\/strong><\/th>\nNumber
    \nof
    \ncontrol
    \naxes<\/strong><\/th>\n    		Cable
    \nlength<\/strong><\/th>\n    		Model<\/strong><\/th>\nStand-
    \nards<\/strong><\/th>\n<\/tr>\n
    Servo
    \nRelay
    \nUnit<\/strong><\/th>\n    		For CJ1W-NC113\/133
    \n(No communication supported)<\/td>\n    		—<\/td>\n1 axis<\/td>\n—<\/td>\nXW2B-20J6-1B<\/strong><\/td>\n—<\/td>\n<\/tr>\n
    For CJ1W-NC213\/233\/413\/433
    \n(No communication supported)<\/td>\n    		—<\/td>\n2 axes<\/td>\n—<\/td>\nXW2B-40J6-2B<\/strong><\/td>\n<\/td>\n<\/tr>\n
    For CJ1W-NC113\/133\/213\/
    \n233\/413\/433
    \n(Communication supported)<\/td>\n    		—<\/td>\n2 axes<\/td>\n—<\/td>\nXW2B-40J6-4A<\/strong><\/td>\n<\/td>\n<\/tr>\n
    Position
    \nControl
    \nUnit
    \nCables
    \nfor
    \nServo
    \nRelay
    \nUnit<\/strong><\/th>\n    		Open-
    \ncollector
    \noutput<\/td>\n    		For CJ1W-NC113<\/td>\nOMNUC G\/G5 Series,
    \nSMARTSTEP 2<\/td>\n    		1 axis<\/td>\n0.5m<\/td>\nXW2Z-050J-A14<\/strong><\/td>\n—<\/td>\n<\/tr>\n
    1m<\/td>\nXW2Z-100J-A14<\/strong><\/td>\n<\/tr>\n
    SMARTSTEP
    \nJunior Series<\/td>\n    		0.5m<\/td>\nXW2Z-050J-A16<\/strong><\/td>\n<\/tr>\n
    1m<\/td>\nXW2Z-100J-A16<\/strong><\/td>\n<\/tr>\n
    For CJ1W-
    \nNC213\/413<\/td>\n    		OMNUC G\/G5 Series,
    \nSMARTSTEP 2<\/td>\n    		2 axes<\/td>\n0.5m<\/td>\nXW2Z-050J-A15<\/strong><\/td>\n<\/tr>\n
    1m<\/td>\nXW2Z-100J-A15<\/strong><\/td>\n<\/tr>\n
    SMARTSTEP
    \nJunior Series<\/td>\n    		0.5m<\/td>\nXW2Z-050J-A17<\/strong><\/td>\n<\/tr>\n
    1m<\/td>\nXW2Z-100J-A17<\/strong><\/td>\n<\/tr>\n
    Line-
    \ndriver
    \noutput<\/td>\n    		For CJ1W-NC313<\/td>\nOMNUC G\/G5 Series,
    \nSMARTSTEP 2<\/td>\n    		1 axis<\/td>\n0.5m<\/td>\nXW2Z-050J-A18<\/strong><\/td>\n<\/tr>\n
    1m<\/td>\nXW2Z-100J-A18<\/strong><\/td>\n<\/tr>\n
    SMARTSTEP
    \nJunior Series<\/td>\n    		0.5m<\/td>\nXW2Z-050J-A20<\/strong><\/td>\n<\/tr>\n
    1m<\/td>\nXW2Z-100J-A20<\/strong><\/td>\n<\/tr>\n
    For CJ1W-
    \nNC233\/413<\/td>\n    		OMNUC G\/G5 Series,
    \nSMARTSTEP 2<\/td>\n    		2 axes<\/td>\n0.5m<\/td>\nXW2Z-050J-A19<\/strong><\/td>\n<\/tr>\n
    1m<\/td>\nXW2Z-100J-A19<\/strong><\/td>\n<\/tr>\n
    SMARTSTEP
    \nJunior Series<\/td>\n    		0.5m<\/td>\nXW2Z-050J-A21<\/strong><\/td>\n<\/tr>\n
    1m<\/td>\nXW2Z-100J-A21<\/strong><\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n<\/div>\n

    Accessories<\/h4>\n
    \n
    \n

    The Position Control Unit includes the 40-pin solder-type connectors C500-CE404 (socket: Fujitsu FCN-361J040-AU, cover: Fujitsu FCN-360C040-J2).<\/p>\n<\/div>\n<\/div>\n

    Applicable Connectors<\/h4>\n
    \n
    \n
    \n\n\n\n\n\n\n\n\n
    Name<\/strong><\/th>\nSpecifications<\/strong><\/td>\nModel<\/strong><\/th>\n<\/tr>\n
    External I\/O Connectors<\/strong><\/th>\n\n
    <\/div>\n<\/td>\n
    		40 pin, soldered, right angle w\/cover (included with the Unit)<\/td>\nC500-CE404<\/strong><\/td>\n<\/tr>\n
    40 pin, crimped right angle w\/cover<\/td>\nC500-CE405<\/strong><\/td>\n<\/tr>\n
    \n
    <\/div>\n<\/td>\n
    		40 pin, Pressure welded, w\/o cover<\/td>\nC500-CE403<\/strong><\/td>\n<\/tr>\n
    \n
    <\/div>\n<\/td>\n
    		40 pin, soldered, w\/cover<\/td>\nC500-CE401<\/strong><\/td>\n<\/tr>\n
    40 pin, crimped w\/cover<\/td>\nC500-CE402<\/strong><\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n<\/div>\n

     <\/p>\n

    Basic Specifications<\/h4>\n
    \n
    \n
    \n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
    Item<\/strong><\/th>\nModel<\/strong><\/td>\n<\/tr>\n
    CJ1W-NC113\/133<\/strong><\/th>\nCJ1W-NC213\/233<\/strong><\/td>\nCJ1W-NC413\/433<\/strong><\/th>\n<\/tr>\n
    Power supply
    \nvoltage<\/strong><\/th>\n    		5 V DC (for the PCU itself)<\/td>\n<\/tr>\n
    24 V DC (external power supply)<\/td>\n<\/tr>\n
    5 V DC (external power supply; line driver output only)<\/td>\n<\/tr>\n
    Allowable power
    \nsupply voltage
    \nrange<\/strong><\/th>\n    		4.75 to 5.25 V DC (for the PCU itself)<\/td>\n<\/tr>\n
    21.6 to 26.4 V DC (external power supply)<\/td>\n22.8 to 25.2 V DC
    \n(external power supply)<\/td>\n<\/tr>\n
    4.75 to 5.25 V DC (external power supply; line driver output only)<\/td>\n<\/tr>\n
    Internal current
    \nconsumption<\/strong><\/th>\n    		250 mA max. at 5 V DC<\/td>\n250 mA max. at 5 V DC<\/td>\n360 mA max. at 5 V DC<\/td>\n<\/tr>\n
    Current
    \nconsumption of
    \nexternal power
    \nsupply<\/strong><\/th>\n    		NC113: 30 mA max. at 24 V DC
    \nNC133: 10 mA max. at 24 V DC
    \nNC133: 60 mA max. at 5 V DC<\/td>\n    		NC213: 50 mA max. at 24 V DC
    \nNC233: 20 mA max. at 24 V DC
    \nNC233: 120 mA max. at 5 V DC<\/td>\n    		NC413: 100 mA max. at 24 V DC
    \nNC433: 30 mA max. at 24 V DC
    \nNC433: 230 mA max. at 5 V DC<\/td>\n<\/tr>\n
    External
    \ndimensions<\/strong><\/th>\n    		90 (H) \u00d7 31 (W) \u00d7 65 (D) (all models)<\/td>\n<\/tr>\n
    Weight<\/strong><\/th>\n100 g max.<\/td>\n100 g max.<\/td>\n150 g max.<\/td>\n<\/tr>\n
    Ambient
    \noperating
    \ntemperature<\/strong><\/th>\n    		0 to 55 \u00b0 C<\/td>\n0 to 50 \u00b0 C *<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n<\/div>\n
    \n
    \n
    Note: Specifications not listed above conform to CJ Series general specifications.
    \n* Refer to Operation Manual 3-3-5 Mounting Precaution for CJ1W-NC413\/NC433 for information on the ambient operating
    \ntemperature of the CJ1W-NC413\/433.<\/div>\n<\/div>\n<\/div>\n

    Performance Specifications<\/h4>\n
    \n
    \n
    \n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
    Item<\/strong><\/th>\nModel<\/strong><\/td>\n<\/tr>\n
    CJ1W-NC113\/133<\/strong><\/th>\nCJ1W-NC213\/233<\/strong><\/td>\nCJ1W-NC413\/433<\/strong><\/th>\n<\/tr>\n
    Applicable PLC models<\/strong><\/th>\nCJ-series PLCs *1<\/td>\n<\/tr>\n
    Unit type<\/strong><\/th>\nSpecial I\/O Unit<\/td>\n<\/tr>\n
    I\/O requirements<\/strong><\/th>\nWords<\/strong><\/td>\n5 words<\/td>\n10 words<\/td>\n20 words<\/td>\n<\/tr>\n
    Controlled driver<\/strong><\/th>\nPulse-train input-type Servo Drive or stepping motor driver
    \nNC113\/213\/413 models have open collector output.
    \nNC133\/233\/433 models have line driver output.<\/td>\n<\/tr>\n
    Control<\/strong><\/th>\nControl system<\/strong><\/td>\nOpen-loop control by pulse train output<\/td>\n<\/tr>\n
    Number of control
    \naxes<\/strong><\/th>\n    		1 axis<\/td>\n2 axes<\/td>\n4 axes<\/td>\n<\/tr>\n
    Control unit<\/strong><\/th>\nPulse<\/td>\n<\/tr>\n
    Positioning operations<\/strong><\/th>\nTwo types: memory operation and direct operation<\/td>\n<\/tr>\n
    Positioning
    \noperations<\/strong><\/th>\n    		Independent<\/strong><\/td>\n1 axis<\/td>\n2 independent axes<\/td>\n4 independent axes<\/td>\n<\/tr>\n
    Linear interpolation<\/strong><\/th>\nNone<\/td>\n2 axes max.<\/td>\n4 axes max.<\/td>\n<\/tr>\n
    Speed control<\/strong><\/th>\n1 axis<\/td>\n2 independent axes<\/td>\n4 independent axes<\/td>\n<\/tr>\n
    Interrupt feeding<\/strong><\/th>\n1 axis<\/td>\n2 independent axes<\/td>\n4 independent axes<\/td>\n<\/tr>\n
    Positions<\/strong><\/th>\nRange<\/strong><\/td>\n-1,073,741,823 to 1,073,741,823 pulses *2<\/td>\n<\/tr>\n
    Data items<\/strong><\/th>\n100\/axis<\/td>\n<\/tr>\n
    Speeds<\/strong><\/th>\nRange<\/strong><\/td>\n1 pps to 500 kpps<\/td>\n<\/tr>\n
    Data items<\/strong><\/th>\n100\/axis<\/td>\n<\/tr>\n
    Acceleration and
    \ndeceleration times<\/strong><\/th>\n    		Range<\/strong><\/td>\n0 to 250 s, until maximum speed is reached.<\/td>\n<\/tr>\n
    Data items<\/strong><\/th>\n9\/axis for acceleration and deceleration each<\/td>\n<\/tr>\n
    Functions and
    \nsettings<\/strong><\/th>\n    		Origin search<\/strong><\/td>\nOrigin proximity input signal: selectable (absent, N.O. or N.C. contact).
    \nOrigin input signal: selectable (N.O. or N.C. contact)
    \nOrigin compensation: -1,073,741,823 to 1,073,741,823 pulses
    \nOrigin search speed: High-speed or proximity-speed can be set.
    \nOrigin detection method: May be set to stop upon origin input signal after proximity input
    \nsignal has turned ON, to stop upon origin input signal after proximity input signal has
    \nturned OFF, to stop upon origin input signal without using proximity input signal, or to stop
    \nupon origin input signal after limit input signal has turned OFF.
    \nN.O. = Normally open
    \nN.C. = Normally closed<\/td>\n<\/tr>\n
    Jogging<\/strong><\/th>\nJogging can be executed at a specified speed.<\/td>\n<\/tr>\n
    Dwell times<\/strong><\/th>\n19\/axis can be set from 0 to 9.99 s (unit: 0.01 s).<\/td>\n<\/tr>\n
    Acceleration\/
    \ndeceleration curves<\/strong><\/th>\n    		Trapezoidal or S-curve (Can be set separately for each axis.)<\/td>\n<\/tr>\n
    Zones<\/strong><\/th>\nZone Flag turns ON when present position is within a specified zone. Three zones can be
    \nset for each axis.<\/td>\n<\/tr>\n
    Software limits<\/strong><\/th>\nCan be set within a range of -1,073,741,823 to 1,073,741,823 pulses.<\/td>\n<\/tr>\n
    Backlash
    \ncompensation<\/strong><\/th>\n    		0 to 9,999 pulses. Compensation speed can also be set.<\/td>\n<\/tr>\n
    Teaching<\/strong><\/th>\nWith a command from the PLC, the present position can be taken as the position data.<\/td>\n<\/tr>\n
    Deceleration stop<\/strong><\/th>\nThe STOP command causes positioning to decelerate to a stop according to the specified
    \ndeceleration time.<\/td>\n<\/tr>\n
    Emergency stop<\/strong><\/th>\nPulse outputs are stopped by an external emergency stop command.<\/td>\n<\/tr>\n
    Present position
    \npreset<\/strong><\/th>\n    		The PRESENT POSITION PRESET command can be used to change the present position
    \nto a specified value.<\/td>\n<\/tr>\n
    Override<\/strong><\/th>\nWhen the override enabling command is executed during positioning, the target speed is
    \nchanged by applying the override coefficient. Possible to set to a value from 1 to 999% (by
    \nan increment of 1%)<\/td>\n<\/tr>\n
    Data saving<\/strong><\/th>\n1) Saving to flash memory. (Can be written 100,000 times.)
    \n2) Reading from PLC area by data reading instruction.
    \n3) Reading by Support Software and saving to personal computer hard disk or floppy disk.<\/td>\n<\/tr>\n
    External I\/O<\/strong><\/th>\nInputs<\/strong><\/td>\nPrepare the following inputs for each axis:
    \nCW and CCW limit input signals, origin proximity input signal, origin input signal, emergency
    \nstop input signal, positioning completed signal, interrupt input signal<\/td>\n<\/tr>\n
    Outputs<\/strong><\/th>\nPrepare the following outputs for each axis:
    \nPulse outputs
    \nCW\/CCW pulses, pulse outputs and direction outputs can be switched.
    \nEither error counter reset or origin-adjustment command outputs can be selected
    \ndepending on the mode.<\/td>\n<\/tr>\n
    Pulse output distribution period<\/strong><\/th>\n1-axis operation: 4 ms
    \nLinear interpolation: 8 ms<\/td>\n<\/tr>\n
    Response time<\/strong><\/th>\nRefer to Operation manual Appendix A Performance Characteristics.<\/td>\n<\/tr>\n
    Self-diagnostic function<\/strong><\/th>\nFlash memory check, memory loss check, CPU bus check<\/td>\n<\/tr>\n
    Error detection function<\/strong><\/th>\nOvertravel, CPU error, software limit over, emergency stop<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n<\/div>\n
    \n
    \n
    *1. The additional functions supported by unit version 2.0 can be used only when the PCU is installed with a CJ1-H or\u00a0CJ1M\u00a0CPU Unit (either CPU Unit Ver. 2.0 or Pre-Ver. 2.0 CPU Unit). These functions cannot be used if the PCU is\u00a0installed with a CJ1 CPU Unit.
    \n*2. When performing linear interpolation, the distances that can be moved will vary.<\/div>\n<\/div>\n<\/div>\n
    <\/div>\n
    \n
    \n
    \n

    (Unit: mm)<\/p>\n<\/div>\n<\/div>\n

    CJ1W-NC113\/213\/413
    \nCJ1W-NC133\/233\/433<\/h4>\n
    \n
    \"CJ1W-NC[][]3<\/div>\n<\/div>\n

    CJ1W-SP001<\/h4>\n
    \n
    \"CJ1W-NC[][]3<\/div>\n<\/div>\n<\/div>\n
    <\/div>\n
    \n\n\n\n\n\n
    \n
    Catalog Name<\/div>\n<\/th>\n
    		\n
    Catalog Number
    \n[size]<\/div>\n<\/th>\n
    		\n
    Last Update<\/div>\n<\/th>\n<\/tr>\n<\/thead>\n
    \"\"\u00a0CJ1W-NC[][]3 Data Sheet<\/a><\/td>\n–
    \n[2673KB]<\/span><\/td>\n    		May 12, 2016<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n","protected":false},"excerpt":{"rendered":"

    High-speed, High-precision positioning with 1, 2, or 4 axes<\/h2>\n","protected":false},"featured_media":1531,"comment_status":"open","ping_status":"closed","template":"","meta":[],"product_cat":[91,63,72],"product_tag":[],"_links":{"self":[{"href":"https:\/\/al-tet-onlinesales.adbridgessolution.com\/index.php\/wp-json\/wp\/v2\/product\/1580"}],"collection":[{"href":"https:\/\/al-tet-onlinesales.adbridgessolution.com\/index.php\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/al-tet-onlinesales.adbridgessolution.com\/index.php\/wp-json\/wp\/v2\/types\/product"}],"replies":[{"embeddable":true,"href":"https:\/\/al-tet-onlinesales.adbridgessolution.com\/index.php\/wp-json\/wp\/v2\/comments?post=1580"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/al-tet-onlinesales.adbridgessolution.com\/index.php\/wp-json\/wp\/v2\/media\/1531"}],"wp:attachment":[{"href":"https:\/\/al-tet-onlinesales.adbridgessolution.com\/index.php\/wp-json\/wp\/v2\/media?parent=1580"}],"wp:term":[{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/al-tet-onlinesales.adbridgessolution.com\/index.php\/wp-json\/wp\/v2\/product_cat?post=1580"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/al-tet-onlinesales.adbridgessolution.com\/index.php\/wp-json\/wp\/v2\/product_tag?post=1580"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}