{"id":1396,"date":"2019-01-02T03:03:37","date_gmt":"2019-01-02T03:03:37","guid":{"rendered":"http:\/\/al-tet-onlinesales.allyoulovetrading.com\/?post_type=product&p=1396"},"modified":"2019-01-02T03:03:37","modified_gmt":"2019-01-02T03:03:37","slug":"nx-cif-2","status":"publish","type":"product","link":"https:\/\/al-tet-onlinesales.adbridgessolution.com\/index.php\/product\/nx-cif-2\/","title":{"rendered":"NX-CIF"},"content":{"rendered":"
\n
\n

\u2022 Just 12 mm wide, saving space in your cabinet.<\/p>\n

\u2022 Three models are available with a choice of one RS-422A\/485, one RS-232C, or two RS-232C ports.<\/p>\n

\u2022 Screwless push-in terminal block (1-port model) and D-Sub connector (2-port model) significantly reduce wiring work.<\/p>\n

\u2022 No-protocol communications are supported as the communications protocol.<\/p>\n

\u2022 The maximum baud rate is 230.4 kbps. The baud rate can be selected to match the connected serial devices.<\/p>\n

\u2022 The settings are backed up and saved in the EtherCAT Coupler Unit. This facilitates commissioning and maintenance.<\/p>\n

\u2022 The serial line monitor enables you to check the communications status with serial devices on the Sysmac Studio for easy and reliable startup of the devices.<\/p>\n<\/div>\n<\/div>\n

\n
\n

Sysmac is a trademark or registered trademark of OMRON Corporation in Japan and other countries for OMRON factory automation products.
\nEtherCAT\u00ae is a registered trademark of Beckhoff Automation GmbH for their patented technology.
\nEtherNet\/IPTM<\/sup>\u00a0is the trademarks of ODVA.
\nOther company names and product names in this document are the trademarks or registered trademarks of their respective companies.<\/p>\n<\/div>\n<\/div>\n

 <\/p>\n

Applicable standards<\/h4>\n
\n
\n

Ask your OMRON representative for the most recent applicable standards for each model.<\/p>\n<\/div>\n<\/div>\n

Communications Interface Units<\/h4>\n
\n
\n
\n\n\n\n\n\n\n
Product name<\/strong><\/th>\nSerial
\ninterface<\/strong><\/th>\n		External connection
\nterminals<\/strong><\/th>\n		Number of
\nserial ports<\/strong><\/th>\n		Communications
\nprotocol<\/strong><\/th>\n		Model<\/strong><\/th>\n<\/tr>\n
Communications
\nInterface Unit
\n\"3479_lu_1_1\"<\/strong><\/th>\n		RS-232C<\/td>\nScrewless Clamping
\nTerminal Block<\/td>\n		1 port<\/td>\nNo-protocol
\nSignal lines<\/td>\n		NX-CIF101<\/strong><\/td>\n<\/tr>\n
RS-422A\/485<\/td>\nNX-CIF105<\/strong><\/td>\n<\/tr>\n
RS-232C<\/td>\nD-Sub connector<\/td>\n2 ports<\/td>\nNX-CIF210<\/strong><\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n<\/div>\n

Optional Products<\/h4>\n
\n
\n
\n\n\n\n\n
Product name<\/strong><\/th>\nSpecification<\/strong><\/th>\nModel<\/strong><\/th>\n<\/tr>\n
Unit\/Terminal Block Coding Pins<\/strong><\/th>\nPins for 10 Units (30 terminal block pins and 30 Unit pins)<\/td>\nNX-AUX02<\/strong><\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n<\/div>\n
\n
\n
\n\n\n\n\n\n
Product name<\/strong><\/th>\nSpecification<\/strong><\/th>\nModel<\/strong><\/th>\n<\/tr>\n
No. of terminals<\/strong><\/th>\nTerminal number
\nindications<\/strong><\/th>\n		Ground terminal
\nmark<\/strong><\/th>\n		Terminal current
\ncapacity<\/strong><\/th>\n<\/tr>\n
Terminal Block *<\/strong><\/th>\n16<\/td>\nA\/B<\/td>\nPresent<\/td>\n10 A<\/td>\nNX-TBC162<\/strong><\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n<\/div>\n
\n
\n

* These options can be used with the NX-CIF101 and NX-CIF105. (They cannot be used with the NX-CIF210.)<\/p>\n<\/div>\n<\/div>\n

Accessories<\/h4>\n
\n
\n

Not included.<\/p>\n<\/div>\n<\/div>\n

 <\/p>\n

General Specification<\/h4>\n
\n
\n
\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
Item<\/strong><\/th>\nSpecification<\/strong><\/th>\n<\/tr>\n
Enclosure<\/strong><\/th>\nMounted in a panel.<\/td>\n<\/tr>\n
Grounding method<\/strong><\/th>\nGround of 100 \u03a9 or less.
\nIf a conductive DIN Track is used, a Communications Interface Units
\nis grounded through the DIN Track from the System Power Supply
\nUnit. If a non-conductive DIN Track is used, a Communications
\nInterface Units is grounded from the FG terminal.<\/td>\n<\/tr>\n
Operating
\nenvironment<\/strong><\/th>\n		Ambient operating
\ntemperature<\/strong><\/th>\n		0 to 55\u00b0C<\/td>\n<\/tr>\n
Ambient operating
\nhumidity<\/strong><\/th>\n		10% to 95% (with no condensation or icing)<\/td>\n<\/tr>\n
Atmosphere<\/strong><\/th>\nMust be free from corrosive gases.<\/td>\n<\/tr>\n
Ambient storage
\ntemperature<\/strong><\/th>\n		-25 to 70\u00b0C (with no condensation or icing)<\/td>\n<\/tr>\n
Altitude<\/strong><\/th>\n2,000 m max.<\/td>\n<\/tr>\n
Pollution degree<\/strong><\/th>\n2 or less: Conforms to JIS B 3502 and IEC 61131-2.<\/td>\n<\/tr>\n
Noise immunity<\/strong><\/th>\n2 kV on power supply line (Conforms to IEC 61000-4-4.)<\/td>\n<\/tr>\n
Overvoltage category<\/strong><\/th>\nCategory II: Conforms to JIS B 3502 and IEC 61131-2.<\/td>\n<\/tr>\n
EMC immunity level<\/strong><\/th>\nZone B<\/td>\n<\/tr>\n
Vibration resistance<\/strong><\/th>\nConforms to IEC 60068-2-6.
\n5 to 8.4 Hz with 3.5-mm amplitude, 8.4 to 150 Hz, Acceleration of
\n9.8 m\/s2<\/sup>, 100 min in X, Y, and Z directions (10 sweeps of 10 min
\neach = 100 min total)<\/td>\n<\/tr>\n
Shock resistance<\/strong><\/th>\nConforms to IEC 60068-2-27. 147 m\/s2<\/sup>, 3 times each in X, Y, and
\nZ directions<\/td>\n<\/tr>\n
Insulation resistance<\/strong><\/th>\n20 M\u03a9 min. between isolated circuits (at 100 VDC)<\/td>\n<\/tr>\n
Dielectric strength<\/strong><\/th>\n510 VAC between isolated circuits for 1 minute with leakage current
\nof 5 mA max.<\/td>\n<\/tr>\n
Applicable standards *<\/strong><\/th>\ncULus: Listed (UL508), ANSI\/ISA 12.12.01, EU: EN 61131-2, NK, LR, RCM,
\nand KC: KC Registration<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n<\/div>\n
\n
\n

* Refer to the OMRON website (http:\/\/www.ia.omron.com\/) or consult your OMRON representative for the most recent applicable standards for each model.<\/p>\n<\/div>\n<\/div>\n

Specifications of Individual Units<\/h4>\n

NX-CIF101<\/h4>\n
\n
\n
\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
Item<\/strong><\/th>\nSpecification<\/strong><\/th>\n<\/tr>\n
Number of ports<\/strong><\/th>\n1<\/td>\n<\/tr>\n
Communications ports<\/strong><\/th>\nRS-232C<\/td>\n<\/tr>\n
Communications protocol<\/strong><\/th>\nNo-protocol<\/td>\n<\/tr>\n
Communications
\nspecifications<\/strong><\/th>\n		Communications method<\/strong><\/th>\nFull duplex<\/td>\n<\/tr>\n
Signal lines *1<\/strong><\/th>\n—<\/td>\n<\/tr>\n
Baud rate [bps] *1<\/strong><\/th>\n1,200, 2,400, 4,800, 9,600, 19,200, 38,400, 57,600,
\n115,200, or 230,400<\/td>\n<\/tr>\n
Data length [bits] *1<\/strong><\/th>\n7 or 8<\/td>\n<\/tr>\n
Parity *1<\/strong><\/th>\nEven, odd, or none<\/td>\n<\/tr>\n
Start bits [bits]<\/strong><\/th>\nAlways 1.<\/td>\n<\/tr>\n
Stop bits [bits] *1<\/strong><\/th>\n1 or 2<\/td>\n<\/tr>\n
Flow control *1<\/strong><\/th>\nNone, RS\/CS flow control, or Xon\/Xoff control<\/td>\n<\/tr>\n
Flow control target *1<\/strong><\/th>\nSend\/receive, send only, or receive only<\/td>\n<\/tr>\n
Initial RS signal value *1 *2<\/strong><\/th>\nON or OFF<\/td>\n<\/tr>\n
Number of characters to
\ndetermine the end *1 *3<\/strong><\/th>\n		0 to 10,000 (in increments of 0.1 character))
\n0: The end is not detected.<\/td>\n<\/tr>\n
Maximum communications
\ndistance [m]<\/strong><\/th>\n		15 *4<\/td>\n<\/tr>\n
Connection configuration<\/strong><\/th>\n1:1<\/td>\n<\/tr>\n
I\/O refreshing method<\/strong><\/th>\nFree-Run refreshing only<\/td>\n<\/tr>\n
PDO data size [bytes] *1<\/strong><\/th>\nInputs or outputs: 4, 8, 12, 16, 20, 24, 28, 32, 36,
\n40, 44, 48, 52, 56, 60, 64, 68, 72, 76, or 80<\/td>\n<\/tr>\n
Transmission buffering enable\/disable setting *1<\/strong><\/th>\nEnabled or disabled<\/td>\n<\/tr>\n
Functions to back up data<\/strong><\/th>\nProvided. *5<\/td>\n<\/tr>\n
Terminating resistance setting<\/strong><\/th>\n—<\/td>\n<\/tr>\n
Isolation method<\/strong><\/th>\nNo isolation<\/td>\n<\/tr>\n
Power consumption<\/strong><\/th>\n\u2022 Connected to a CPU Unit
\n1.10 W max.
\n\u2022 Connected to a Communications Coupler Unit
\n0.90 W max.<\/td>\n<\/tr>\n
Weight<\/strong><\/th>\n66 g max.<\/td>\n<\/tr>\n
Installation orientation and restrictions<\/strong><\/th>\nInstallation orientation:
\n\u2022 Connected to a CPU Unit: Possible in upright installation.
\n\u2022 Connected to a Communications Coupler Unit:
\nPossible in 6 orientations.
\nRestrictions: There are no restrictions.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n<\/div>\n
\n
\n

*1. Setting is possible in the Unit operation settings of the Sysmac Studio.
\n*2. This is the value of the RS signal when the port enters the Operational state or immediately after the port is restarted.
\nThe initial value is disabled when RS\/CS flow control is set.
\n*3. This setting is provided for communications protocols that assume the end of the data if data is not received for a
\nspecific period of time. For example, if the number of characters to determine the end is set to 35, the end of the
\ndata will be assumed if data is not received for the time required to receive 3.5 characters.
\n*4. If the baud rate is set to higher than 19,200 bps, refer to the manual for the remote communications device.
\n*5. The settings that are backed up are saved in memory in the Communications Coupler Unit. The settings that are
\nbacked up are not saved in the Communications Interface Units.<\/p>\n<\/div>\n<\/div>\n

NX-CIF105<\/h4>\n
\n
\n
\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
Item<\/strong><\/th>\nSpecification<\/strong><\/th>\n<\/tr>\n
Number of ports<\/strong><\/th>\n1<\/td>\n<\/tr>\n
Communications ports<\/strong><\/th>\nRS-422A\/485<\/td>\n<\/tr>\n
Communications protocol<\/strong><\/th>\nNo-protocol<\/td>\n<\/tr>\n
Communications
\nspecifications<\/strong><\/th>\n		Communications method<\/strong><\/th>\nHalf duplex for two-wire connection, Full duplex for
\nfour-wire connection<\/td>\n<\/tr>\n
Signal lines *1<\/strong><\/th>\nTwo lines or four lines<\/td>\n<\/tr>\n
Baud rate [bps] *1<\/strong><\/th>\n1,200, 2,400, 4,800, 9,600, 19,200, 38,400, 57,600,
\n115,200, or 230,400<\/td>\n<\/tr>\n
Data length [bits] *1<\/strong><\/th>\n7 or 8<\/td>\n<\/tr>\n
Parity *1<\/strong><\/th>\nEven, odd, or none<\/td>\n<\/tr>\n
Start bits [bits]<\/strong><\/th>\nAlways 1.<\/td>\n<\/tr>\n
Stop bits [bits] *1<\/strong><\/th>\n1 or 2<\/td>\n<\/tr>\n
Flow control *1<\/strong><\/th>\nNone or Xon\/Xoff control<\/td>\n<\/tr>\n
Flow control target *1<\/strong><\/th>\nSend\/receive, send only, or receive only<\/td>\n<\/tr>\n
Initial RS signal value *1 *2<\/strong><\/th>\nON or OFF<\/td>\n<\/tr>\n
Number of characters to
\ndetermine the end *1 *3<\/strong><\/th>\n		0 to 10,000 (in increments of 0.1 character))
\n0: The end is not detected.<\/td>\n<\/tr>\n
Maximum communications
\ndistance [m]<\/strong><\/th>\n		1,200 *4<\/td>\n<\/tr>\n
Connection configuration<\/strong><\/th>\n1:N
\nMaximum value of N is 32.
\nYou can change between two-wire and four-wire
\nconnections.<\/td>\n<\/tr>\n
I\/O refreshing method<\/strong><\/th>\nFree-Run refreshing only<\/td>\n<\/tr>\n
PDO data size [bytes] *1<\/strong><\/th>\nInputs or outputs: 4, 8, 12, 16, 20, 24, 28, 32, 36,
\n40, 44, 48, 52, 56, 60, 64, 68, 72, 76, or 80<\/td>\n<\/tr>\n
Transmission buffering enable\/disable setting *1<\/strong><\/th>\nEnabled or disabled<\/td>\n<\/tr>\n
Functions to back up data<\/strong><\/th>\nProvided. *5<\/td>\n<\/tr>\n
Terminating resistance setting<\/strong><\/th>\nPossible<\/td>\n<\/tr>\n
Isolation method<\/strong><\/th>\nPower supply: transformer and photocoupler
\nSignals: Digital isolators<\/td>\n<\/tr>\n
Power consumption<\/strong><\/th>\n\u2022 Connected to a CPU Unit
\n1.65 W max.
\n\u2022 Connected to a Communications Coupler Unit
\n1.45 W max.<\/td>\n<\/tr>\n
Weight<\/strong><\/th>\n69 g max.<\/td>\n<\/tr>\n
Installation orientation and restrictions<\/strong><\/th>\nInstallation orientation:
\n\u2022 Connected to a CPU Unit: Possible in upright installation.
\n\u2022 Connected to a Communications Coupler Unit:
\nPossible in 6 orientations.
\nRestrictions: There are no restrictions.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n<\/div>\n
\n
\n

*1. Setting is possible in the Unit operation settings of the Sysmac Studio.
\n*2. This is the value of the RS signal when the port enters the Operational state or immediately after the port is restarted.
\nThe initial value is disabled when RS\/CS flow control is set. It is also disabled for the NX-CIF105.
\n*3. This setting is provided for communications protocols that assume the end of the data if data is not received for a
\nspecific period of time. For example, if the number of characters to determine the end is set to 35, the end of the
\ndata will be assumed if data is not received for the time required to receive 3.5 characters.
\n*4. The maximum total cable length for multidrop connections is 1,200 m.
\n*5. The settings that are backed up are saved in memory in the Communications Coupler Unit. The settings that are
\nbacked up are not saved in the Communications Interface Units.<\/p>\n<\/div>\n<\/div>\n

NX-CIF210<\/h4>\n
\n
\n
\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
Item<\/strong><\/th>\nSpecification<\/strong><\/th>\n<\/tr>\n
Number of ports<\/strong><\/th>\n2<\/td>\n<\/tr>\n
Communications ports<\/strong><\/th>\nRS-232C<\/td>\n<\/tr>\n
Communications protocol<\/strong><\/th>\nNo-protocol<\/td>\n<\/tr>\n
Communications
\nspecifications<\/strong><\/th>\n		Communications method<\/strong><\/th>\nFull duplex<\/td>\n<\/tr>\n
Signal lines *1<\/strong><\/th>\n—<\/td>\n<\/tr>\n
Baud rate [bps] *1<\/strong><\/th>\n1,200, 2,400, 4,800, 9,600, 19,200, 38,400, 57,600,
\n115,200, or 230,400<\/td>\n<\/tr>\n
Data length [bits] *1<\/strong><\/th>\n7 or 8<\/td>\n<\/tr>\n
Parity *1<\/strong><\/th>\nEven, odd, or none<\/td>\n<\/tr>\n
Start bits [bits]<\/strong><\/th>\nAlways 1.<\/td>\n<\/tr>\n
Stop bits [bits] *1<\/strong><\/th>\n1 or 2<\/td>\n<\/tr>\n
Flow control *1<\/strong><\/th>\nNone, RS\/CS flow control, or Xon\/Xoff control<\/td>\n<\/tr>\n
Flow control target *1<\/strong><\/th>\nSend\/receive, send only, or receive only<\/td>\n<\/tr>\n
Initial RS signal value *1 *2<\/strong><\/th>\nON or OFF<\/td>\n<\/tr>\n
Number of characters to
\ndetermine the end *1 *3<\/strong><\/th>\n		0 to 10,000 (in increments of 0.1 character))
\n0: The end is not detected.<\/td>\n<\/tr>\n
Maximum communications
\ndistance [m]<\/strong><\/th>\n		15 *4<\/td>\n<\/tr>\n
Connection configuration<\/strong><\/th>\n1:1<\/td>\n<\/tr>\n
I\/O refreshing method<\/strong><\/th>\nFree-Run refreshing only<\/td>\n<\/tr>\n
PDO data size [bytes] *1<\/strong><\/th>\nInputs or outputs: 4, 8, 12, 16, 20, 24, 28, 32, 36,
\n40, 44, 48, 52, 56, 60, 64, 68, 72, 76, or 80<\/td>\n<\/tr>\n
Transmission buffering enable\/disable setting *1<\/strong><\/th>\nEnabled or disabled<\/td>\n<\/tr>\n
Functions to back up data<\/strong><\/th>\nProvided. *5<\/td>\n<\/tr>\n
Terminating resistance setting<\/strong><\/th>\n—<\/td>\n<\/tr>\n
Isolation method<\/strong><\/th>\nNo isolation<\/td>\n<\/tr>\n
Power consumption<\/strong><\/th>\n\u2022 Connected to a CPU Unit
\n1.15 W max.
\n\u2022 Connected to a Communications Coupler Unit
\n0.95 W max.<\/td>\n<\/tr>\n
Weight<\/strong><\/th>\n91 g max.<\/td>\n<\/tr>\n
Installation orientation and restrictions<\/strong><\/th>\nInstallation orientation:
\n\u2022 Connected to a CPU Unit: Possible in upright installation.
\n\u2022 Connected to a Communications Coupler Unit:
\nPossible in 6 orientations.
\nRestrictions: There are no restrictions.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n<\/div>\n
\n
\n

*1. Setting is possible in the Unit operation settings of the Sysmac Studio.
\n*2. This is the value of the RS signal when the port enters the Operational state or immediately after the port is restarted.
\nThe initial value is disabled when RS\/CS flow control is set.
\n*3. This setting is provided for communications protocols that assume the end of the data if data is not received for a
\nspecific period of time. For example, if the number of characters to determine the end is set to 35, the end of the
\ndata will be assumed if data is not received for the time required to receive 3.5 characters.
\n*4. If the baud rate is set to higher than 19,200 bps, refer to the manual for the remote communications device.
\n*5. The settings that are backed up are saved in memory in the Communications Coupler Unit. The settings that are
\nbacked up are not saved in the Communications Interface Units.<\/p>\n<\/div>\n<\/div>\n

Version Information<\/h4>\n

Connecting with CPU Units<\/h4>\n
\n
\n

Refer to the user’s manual for the CPU Unit for the CPU Unit to which NX Units can be connected.<\/p>\n<\/div>\n<\/div>\n

\n
\n
\n\n\n\n\n\n\n\n
NX Unit<\/strong><\/th>\nCorresponding unit versions\/versions<\/strong><\/th>\n<\/tr>\n
Model<\/strong><\/th>\nUnit version<\/strong><\/th>\nCPU Unit<\/strong><\/th>\nSysmac Studio<\/strong><\/th>\n<\/tr>\n
NX-CIF101<\/td>\nVer.1.0<\/td>\nVer.1.13<\/td>\nVer.1.17<\/td>\n<\/tr>\n
NX-CIF105<\/td>\n<\/tr>\n
NX-CIF210<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n<\/div>\n
\n
\n
Note: Some Units do not have all of the versions given in the table. If a Unit does not have the specified version, support is
\nprovided by the oldest available version after the specified version. Refer to the user’s manuals for the specific Units
\nfor the relation between models and versions.<\/div>\n<\/div>\n<\/div>\n

Connecting with an EtherCAT Coupler Unit<\/h4>\n
\n
\n
\n\n\n\n\n\n\n\n
NX Unit<\/strong><\/th>\nCorresponding unit versions\/versions<\/strong><\/th>\n<\/tr>\n
Model<\/strong><\/th>\nUnit version<\/strong><\/th>\nEtherCAT Coupler Unit<\/strong><\/th>\nCPU Units or Industrial PCs *<\/strong><\/th>\nSysmac Studio<\/strong><\/th>\n<\/tr>\n
NX-CIF101<\/td>\nVer.1.0<\/td>\nVer.1.0<\/td>\nVer.1.11<\/td>\nVer.1.15<\/td>\n<\/tr>\n
NX-CIF105<\/td>\n<\/tr>\n
NX-CIF210<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n<\/div>\n
\n
\n
Note: Some Units do not have all of the versions given in the above table. If a Unit does not have the specified version,
\nsupport is provided by the oldest available version after the specified version. Refer to the user’s manuals for the
\nspecific Units for the relation between models and versions.
\n* The serial communications instructions for the CIF Units are supported by CPU Units with unit version 1.11 or later. If it is
\nnot used, it is available for a CPU Unit with unit version 1.10. Refer to the Instructions Reference Manual for the CPU Unit
\nor Industrial PC for the serial communications instructions for the CIF Units.<\/div>\n<\/div>\n<\/div>\n

Connecting with an EtherNet\/IP Coupler Unit<\/h4>\n
\n
\n
\n\n\n\n\n\n\n\n\n
NX Unit<\/strong><\/th>\nCorresponding unit versions\/versions<\/strong><\/th>\n<\/tr>\n
Model<\/strong><\/th>\nUnit
\nversion<\/strong><\/th>\n		Application with an NJ\/NX\/NY-series
\nController *1<\/strong><\/th>\n		Application with a CS\/CJ\/CP-series PLC
\n*2<\/strong><\/th>\n<\/tr>\n
EtherNet\/IP
\nCoupler Unit *3<\/strong><\/th>\n		CPU Unit or
\nIndustrial PC<\/strong><\/th>\n		Sysmac
\nStudio<\/strong><\/th>\n		EtherNet\/IP
\nCoupler Unit *3<\/strong><\/th>\n		Sysmac
\nStudio<\/strong><\/th>\n		NX-IO
\nConfigurator *4<\/strong><\/th>\n<\/tr>\n
NX-CIF101<\/td>\nVer.1.0<\/td>\nVer.1.2<\/td>\nVer.1.14<\/td>\nVer.1.19<\/td>\nVer.1.2<\/td>\nVer.1.19<\/td>\nVer.1.00<\/td>\n<\/tr>\n
NX-CIF105<\/td>\n<\/tr>\n
NX-CIF210<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n<\/div>\n
\n
\n
Note: Some Units do not have all of the versions given in the above table. If a Unit does not have the specified version,
\nsupport is provided by the oldest available version after the specified version. Refer to the user’s manuals for the
\nspecific Units for the relation between models and versions.
\n*1 Refer to the user\u2019s manual for the EtherNet\/IP Coupler Units for information on the unit versions of EtherNet\/IP Units
\nthat are compatible with EtherNet\/IP Coupler Units.
\n*2 Refer to the user\u2019s manual for the EtherNet\/IP Coupler Units for information on the unit versions of CPU Units and
\nEtherNet\/IP Units that are compatible with EtherNet\/IP Coupler Units.
\n*3 Serial communications instructions for CIF Units cannot be used if they are connected to an EtherNet\/IP Coupler Unit.
\n*4 For connection to an EtherNet\/IP Coupler Unit with unit version 1.0, You can connect only to the peripheral USB port on
\nthe EtherNet\/IP Coupler Unit. You cannot connect with any other path. If you need to connect by another path, use an
\nEtherNet\/IP Coupler Unit with unit version 1.2 or later.<\/div>\n<\/div>\n<\/div>\n
<\/div>\n
<\/div>\n
\n
\n
\n

(Unit: mm)<\/p>\n<\/div>\n<\/div>\n

\n
\n

NX-CIF101 and NX-CIF105<\/strong><\/p>\n<\/div>\n

\"NX-CIF<\/div>\n<\/div>\n
\n
\n

NX-CIF210<\/strong><\/p>\n<\/div>\n

\"NX-CIF<\/div>\n<\/div>\n<\/div>\n
<\/div>\n
<\/div>\n
\n\n\n\n\n\n\n
\n
Catalog Name<\/div>\n<\/th>\n
\n
Catalog Number
\n[size]<\/div>\n<\/th>\n
\n
Last Update<\/div>\n<\/th>\n<\/tr>\n<\/thead>\n
\"\"\u00a0NX-CIF Data Sheet<\/a><\/td>\n–
\n[2315KB]<\/span><\/td>\n		Aug 01, 2018<\/td>\n<\/tr>\n
\"\"\u00a0NX-series I\/O System Catalog<\/a><\/td>\nR183-E1-09
\n[6683KB]<\/span><\/td>\n		Nov 01, 2018<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n","protected":false},"excerpt":{"rendered":"

Provides simplicity and flexibility in connecting serial devices to EtherCAT<\/h2>\n","protected":false},"featured_media":1397,"comment_status":"open","ping_status":"closed","template":"","meta":[],"product_cat":[98,63,72],"product_tag":[],"_links":{"self":[{"href":"https:\/\/al-tet-onlinesales.adbridgessolution.com\/index.php\/wp-json\/wp\/v2\/product\/1396"}],"collection":[{"href":"https:\/\/al-tet-onlinesales.adbridgessolution.com\/index.php\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/al-tet-onlinesales.adbridgessolution.com\/index.php\/wp-json\/wp\/v2\/types\/product"}],"replies":[{"embeddable":true,"href":"https:\/\/al-tet-onlinesales.adbridgessolution.com\/index.php\/wp-json\/wp\/v2\/comments?post=1396"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/al-tet-onlinesales.adbridgessolution.com\/index.php\/wp-json\/wp\/v2\/media\/1397"}],"wp:attachment":[{"href":"https:\/\/al-tet-onlinesales.adbridgessolution.com\/index.php\/wp-json\/wp\/v2\/media?parent=1396"}],"wp:term":[{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/al-tet-onlinesales.adbridgessolution.com\/index.php\/wp-json\/wp\/v2\/product_cat?post=1396"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/al-tet-onlinesales.adbridgessolution.com\/index.php\/wp-json\/wp\/v2\/product_tag?post=1396"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}